How To Start A Flooded Stihl Concrete Saw
Starting a flooded Stihl concrete saw can be a frustrating experience, but with the right knowledge and technique, you can get your saw up and running quickly. The concrete saw is an essential tool for construction and demolition work, and it’s important to know how to start it properly to avoid damage and ensure optimal performance.
If your Stihl concrete saw is flooded, it means that there is too much fuel in the engine, making it difficult to start. This can happen if you’ve been using the saw at an angle or if you’ve been starting it without fully engaging the choke. Luckily, there are a few steps you can take to fix the problem and get your saw running smoothly again.
First, you’ll need to locate the choke lever on your saw. This is typically located on the side or front of the engine, and it’s usually labeled with the word “choke.” Once you’ve found it, push the lever all the way up or to the “choke” position. This will close off the air supply, creating a richer fuel mixture that will help to start the engine.
Next, you’ll need to turn off the ignition switch. This will prevent the spark plug from igniting the fuel mixture while you’re trying to start the saw. Once the ignition switch is off, pull the starter rope several times to clear out any excess fuel in the engine. This will help to reduce the flooding and make it easier to start the saw.
Once you’ve cleared out the excess fuel, you’ll need to re-engage the choke lever. This time, push it all the way down or to the “run” position. This will allow air to enter the engine, creating a leaner fuel mixture that is easier to ignite. With the choke engaged, turn on the ignition switch and pull the starter rope to start the saw. It may take a few tries, but with the right technique, you should be able to get the engine running smoothly again.
Starting a flooded Stihl concrete saw can be a bit tricky, but by following these steps and using the proper technique, you can get your saw back up and running in no time. Remember to always read the manufacturer’s instructions and follow safety guidelines when working with power tools. With a little practice, you’ll be able to start your saw with ease and tackle any construction or demolition project with confidence.
Clearing Water From A Flooded Stihl Concrete Saw
If your Stihl concrete saw has been submerged in water or exposed to heavy rain, it is likely that water has entered the engine, leading to flooding. To get your saw up and running again, it is important to clear the water from the engine. Follow these steps to fix a flooded Stihl concrete saw:
- Disconnect the spark plug: Before attempting any repairs or maintenance, make sure the saw is turned off and the spark plug wire is disconnected. This will prevent any accidental startup and ensure your safety.
- Remove the air filter: Use a screwdriver to remove the air filter cover on the saw. Take out the air filter and inspect it for any signs of water or damage. If the filter is wet, it will need to be dried or replaced.
- Drain the fuel tank: Locate the fuel tank on your saw and carefully empty it of any remaining fuel. Be sure to dispose of the fuel properly according to local regulations.
- Drain the carburetor: Use a small container to catch any fuel that may come out. Locate the carburetor drain screw, usually located on the bottom of the carburetor, and unscrew it to allow any water or fuel to drain out. Once drained, securely tighten the screw back into place.
- Dry the spark plug: Remove the spark plug from the engine and wipe it dry using a clean cloth. Check the spark plug for any signs of damage or wear, and replace it if necessary.
- Crank the engine: With the spark plug still detached, pull the starter cord a few times to spin the engine and expel any remaining water. This will help dry out the engine and remove any residual moisture.
- Reassemble and test: Once you have completed all the previous steps, reassemble the saw by reattaching the spark plug and air filter. Double-check that all connections are secure and give the saw a thorough inspection. Finally, reconnect the spark plug wire and try starting the saw. It should now start up and run smoothly.
Remember to always take the necessary precautions when handling power tools and ensure you are working in a safe environment. If you are unsure or uncomfortable preforming any of these steps, it may be best to seek professional assistance.
Essential Tools for Starting a Flooded Stihl Concrete Saw
Starting a flooded Stihl concrete saw can be a frustrating experience, but having the right tools on hand can make the process much easier. Here are some essential tools that you should have in your toolbox to effectively start a flooded Stihl concrete saw:
1. Spark Plug Wrench
A spark plug wrench is a must-have tool for starting a flooded Stihl concrete saw. This wrench allows you to easily remove the spark plug, which is often the cause of a flooded engine. By removing the spark plug, you can check for any fouling or debris and clean or replace it if necessary.
2. Primer Bulb
A primer bulb is another essential tool for starting a flooded Stihl concrete saw. This small rubber bulb is located on the side of the saw and is used to manually prime the engine with fuel. By pressing the primer bulb multiple times, you can help remove excess fuel from the carburetor and make starting the saw easier.
| Tool | Description |
|---|---|
| Spark Plug Wrench | A wrench used to remove the spark plug from the engine. |
| Primer Bulb | A small rubber bulb used to manually prime the engine with fuel. |
These are just a few of the essential tools that you should have on hand when starting a flooded Stihl concrete saw. It’s important to ensure that your tools are in good condition and easily accessible so that you can quickly and effectively start your saw in the event of a flooding.
Step-by-Step Guide to Starting a Flooded Stihl Concrete Saw
Starting a flooded Stihl concrete saw can be a frustrating experience, but with the right steps, you can get your saw running smoothly again. Follow this step-by-step guide to start a flooded Stihl concrete saw:
| Step 1: | Begin by turning the on/off switch to the “off” position. This will prevent any accidental starting and provide a safe working environment. |
| Step 2: | Next, locate the choke lever on your Stihl concrete saw. The choke lever is typically located on the side or top of the saw’s carburetor. |
| Step 3: | Move the choke lever to the “closed” or “choke” position. This will restrict the airflow to the carburetor, allowing for easier starting of the flooded saw. |
| Step 4: | Hold the throttle trigger fully open. This will help clear any excess fuel from the engine and allow for a faster start. |
| Step 5: | Pull the starter rope briskly with one smooth motion. Be sure to keep a firm grip on both the handle and the starter rope. Repeat this step as necessary until the saw starts. |
| Step 6: | If the saw fails to start after several attempts, move the choke lever to the “open” or “run” position. This will allow for normal airflow to the carburetor. |
| Step 7: | Repeat steps 4 and 5 to try starting the saw again. If the saw still does not start, it may be necessary to consult a professional or the manufacturer for further assistance. |
By following these steps, you can effectively start a flooded Stihl concrete saw and get back to your cutting tasks with ease. Remember to always prioritize safety and consult the saw’s manual for specific instructions.
Troubleshooting Tips for Starting a Flooded Stihl Concrete Saw
Starting a flooded Stihl concrete saw can be a frustrating experience. However, with a few troubleshooting tips, you can get your saw up and running again in no time. Here are some steps to help you troubleshoot a flooded Stihl concrete saw:
- Check the fuel level: Ensure that the saw has an adequate amount of fuel. If the fuel level is low, refill the tank with fresh gasoline.
- Inspect the spark plug: Remove the spark plug and examine it for any signs of damage or fouling. Clean or replace the spark plug if necessary.
- Remove excess fuel: If the saw is flooded, you may need to remove the excess fuel from the engine. Turn off the ignition, remove the spark plug, and pull the starter cord several times to clear out the fuel.
- Check the air filter: A dirty or clogged air filter can prevent the saw from starting. Remove the air filter and clean or replace it if necessary.
- Check the carburetor: The carburetor may need to be adjusted or cleaned if the saw is flooded. Refer to the saw’s manual for specific instructions on carburetor maintenance.
- Let the saw dry out: If all else fails, let the saw sit for a while to allow the excess fuel to evaporate. Attempt to start the saw again once it has dried out.
Remember to always consult the manufacturer’s manual for detailed instructions on troubleshooting and maintaining your specific Stihl concrete saw model. Following these troubleshooting tips can help you resolve starting issues and get your flooded Stihl concrete saw back in working condition.
Safety Precautions When Starting a Flooded Stihl Concrete Saw
Starting a flooded Stihl concrete saw can be dangerous if not done properly. Here are some important safety precautions to follow:
- Wear Personal Protective Equipment (PPE): Before starting the saw, make sure you are wearing proper PPE, including goggles, ear protection, and work gloves. This will help protect you from any potential injuries.
- Inspect the Saw: Before attempting to start a flooded saw, inspect it for any damage or loose parts. Make sure the handles, spark plug, and air filter are in good condition. If you notice any issues, do not start the saw and have it repaired by a professional.
- Find a Safe Work Area: Make sure you are in a well-ventilated area with plenty of space for maneuvering the saw. Clear the work area of any debris or obstacles that could cause you to trip or fall.
- Check Fuel and Oil Levels: Ensure the saw has enough fuel and oil before attempting to start it. Use the correct fuel and oil mixture as specified in the manufacturer’s manual. Never overfill the fuel tank.
- Prime the Engine: If the saw is flooded, prime the engine by pressing the primer bulb a few times. This will help remove excess fuel from the carburetor and improve starting.
- Set the Choke and Throttle: Set the choke lever to the closed position and engage the throttle lock. This will provide the necessary air and fuel mixture for starting.
- Hold the Saw Properly: Hold the saw firmly with both hands, ensuring a secure grip on the handles. Keep your body positioned to the side of the saw to avoid any potential kickback.
- Pull the Starter Rope: Pull the starter rope with a quick, smooth motion. Do not yank or jerk the rope as this could result in injury. If the saw does not start on the first attempt, allow it to rest for a few minutes before trying again.
- Monitor the Saw: Once the saw is started, monitor it closely for any unusual noises or vibrations. If you notice anything abnormal, stop the saw immediately and have it checked by a professional.
- Properly Shutdown the Saw: When you are done using the saw, let it idle for a few minutes to cool down. Turn off the engine and remove any debris or dust from the saw before storing it.
By following these safety precautions, you can ensure a safer and more successful start for your flooded Stihl concrete saw.
Preventing a Flooded Stihl Concrete Saw in the Future
Dealing with a flooded Stihl concrete saw can be a frustrating experience, but with proper maintenance and usage habits, you can prevent this issue from occurring in the future. Here are some tips to help you avoid a flooded engine:
1. Use fresh fuel
Ensure that you are using fresh fuel in your Stihl concrete saw. Fuel can degrade over time, leading to engine problems. It is recommended to use fuel that is no more than 30 days old.
2. Properly mix fuel and oil
Always follow the manufacturer’s guidelines for fuel and oil mixing ratios. Using the wrong ratio can cause engine flooding. Measure the fuel and oil accurately to achieve the right mixture.
3. Prime the engine correctly
When starting your Stihl concrete saw, make sure to prime the engine as per the instruction manual. Over-priming can flood the engine and make it difficult to start. Follow the recommended priming procedure for your specific model.
4. Warm up the engine
Before you start cutting, warm up the engine for a few minutes. This will allow the engine to reach its optimal operating temperature and reduce the chances of it flooding during use.
5. Properly store the saw
When you’re done using the Stihl concrete saw, properly store it. Empty the fuel tank, and run the engine until it stops to remove any fuel from the carburetor. This prevents fuel from sitting in the carburetor and causing issues the next time you go to start the saw.
By following these tips, you can ensure that your Stihl concrete saw starts smoothly every time without the frustration of a flooded engine. Regular maintenance and proper usage habits are key to preventing this issue in the future.
Questions and answers
What should I do if my Stihl concrete saw gets flooded?
If your Stihl concrete saw gets flooded, the first thing you should do is turn off the ignition and fuel supply. Then, remove the spark plug and pull the starter cord a few times to clear any excess fuel from the cylinder. After that, clean or replace the spark plug and reinstall it. Finally, start the saw according to the manufacturer’s instructions.
What can cause a Stihl concrete saw to become flooded?
There are a few common reasons that can cause a Stihl concrete saw to become flooded. One reason is overpriming the engine, which means pumping too much fuel into the carburetor. Another reason can be a clogged air filter, which restricts the air flow and leads to an overly rich fuel mixture. Additionally, leaving the choke on for too long when starting the saw can also cause flooding.
Is it possible to prevent a Stihl concrete saw from flooding?
While it is not always possible to completely prevent a Stihl concrete saw from flooding, there are several steps you can take to minimize the risk. First, make sure to follow the manufacturer’s instructions for starting the saw, including the proper use of the choke. Additionally, avoid overpriming the engine and keep the air filter clean and free from debris. Regular maintenance, such as cleaning and adjusting the carburetor, can also help prevent flooding.
Harrison Clayton
Meet Harrison Clayton, a distinguished author and home remodeling enthusiast whose expertise in the realm of renovation is second to none. With a passion for transforming houses into inviting homes, Harrison's writing at https://thehuts-eastbourne.co.uk/ brings a breath of fresh inspiration to the world of home improvement. Whether you're looking to revamp a small corner of your abode or embark on a complete home transformation, Harrison's articles provide the essential expertise and creative flair to turn your visions into reality. So, dive into the captivating world of home remodeling with Harrison Clayton and unlock the full potential of your living space with every word he writes.
