How To Desolder Using Soldering Iron

Soldering is a common technique used in electronics to join two or more components together. However, there may come a time when you need to remove a component, either because it is faulty or you want to replace it with a new one. This process is called desoldering, and it requires a different set of skills and tools compared to soldering. In this article, we will guide you through the steps of desoldering using a soldering iron.

Step 1: Prepare your work area

Before you start desoldering, it is important to create a clean and organized work area. Make sure you have a well-ventilated space to work in, as the process of desoldering can release fumes. Gather all the necessary tools, including a soldering iron with a desoldering tip, desoldering braid or pump, and safety equipment such as goggles and heat-resistant gloves.

Step 2: Heat up the soldering iron

Once you have set up your work area, it’s time to heat up the soldering iron. Plug it in and let it warm up for a few minutes. Make sure the soldering iron is at the correct temperature for desoldering. The ideal temperature may vary depending on the type of solder you are working with, so refer to the manufacturer’s guidelines if you are unsure.

3.0mm Desoldering Braid Wick Wire Flux Solder Remover Soldering Accessories
3.0mm Desoldering Braid Wick Wire Flux Solder Remover Soldering Accessories
£4.15
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

Step 3: Prepare the component for desoldering

Before you can start the desoldering process, you need to prepare the component and the solder joints. Trim any excess leads or wires attached to the component to make it easier to work with. If there is a significant amount of solder on the joints, you may need to use a soldering braid or pump to remove some of it before desoldering.

Step 4: Desolder the component

Now it’s time to desolder the component. Place the desoldering braid or pump on the solder joint, and apply the heated soldering iron to the braid or pump. The heat will cause the solder to melt and be absorbed by the braid or sucked into the pump. Gently wiggle the component while applying heat to the joint to remove it once the solder has melted.

Step 5: Clean the desoldered area

TOWOT Solder Wick Braid with Flux No-Clean Electronic, Desoldering Wick Braid Remover.Desolder Soldering 2.5mm W 0.10'' L 5'
TOWOT Solder Wick Braid with Flux No-Clean Electronic, Desoldering Wick Braid Remover.Desolder Soldering 2.5mm W 0.10'' L 5'
£4.99
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

After removing the component, clean the desoldered area with a soldering iron tip cleaner or a damp sponge. This will remove any remaining solder and flux residue, ensuring a clean and reliable joint for the new component.

Desoldering can be a delicate and precise process, requiring patience and practice. Following these steps will help you desolder components successfully using a soldering iron. Remember to work carefully and safely, taking breaks if needed, to ensure the best results.

What is Desoldering

Desoldering is the process of removing solder from electronic components or connections to repair or replace them. Solder is a metal alloy used to join two or more metal parts together, creating a strong, reliable electrical connection. However, when electronic components need to be replaced or repaired, the existing solder connections must be desoldered to remove the component without damaging the surrounding circuitry.

Desoldering is a skill that is essential for any electronics enthusiast or technician. It involves heating the solder joint with a soldering iron to melt and remove the solder. Proper desoldering techniques are important to ensure that the component is removed safely and without causing any damage to the circuit board or other nearby components.

The Importance of Desoldering

Desoldering is an important skill in electronics because it allows for the repair and replacement of electronic components. Electronic components can fail or become damaged over time due to various reasons such as wear and tear, overheating, or electrical faults. Desoldering allows technicians to safely remove and replace these components, extending the lifespan of the device or equipment.

iFixit Desoldering Pump, Solder Remover Tool with Powerful Suction Force, Suck up Molten, Liquid Solder and desolder Joints Faster, Easier and Safer
iFixit Desoldering Pump, Solder Remover Tool with Powerful Suction Force, Suck up Molten, Liquid Solder and desolder Joints Faster, Easier and Safer
£5.09
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

Desoldering is also crucial in the process of salvaging or reusing electronic components. By desoldering components from old or faulty circuit boards, technicians can recover valuable components that can be used in other projects or repairs. This helps reduce electronic waste and encourages recycling in the electronics industry.

See also  How Not To Hold A Soldering Iron

Tools for Desoldering

When it comes to desoldering, having the right tools can make all the difference. Here are some essential tools you’ll need:

  • Soldering Iron: A soldering iron with adjustable temperature settings is important for desoldering. It should have a fine tip that can melt the solder effectively without damaging the electronic components.
  • Solder Sucker: Also known as a desoldering pump, a solder sucker is a device used to remove molten solder. It consists of a plunger and a heat-resistant tip that creates a vacuum to suck up the solder. It is an essential tool for easily removing excess solder from a joint.
  • Solder Wick: Solder wick, also known as desoldering braid, is a braided copper wire coated with flux. It is used to remove excess solder by absorbing it into the wire. Solder wick is especially useful for removing solder from small, hard-to-reach areas or for cleaning up messy solder joints.
  • Flush Cutters: Flush cutters are used to trim excess leads or wires after desoldering. They have a flat cutting edge that allows for a clean and precise cut close to the surface.
  • Flux Pen: Flux is a chemical compound that helps clean and prepare the surfaces for soldering and desoldering. A flux pen is a convenient tool for applying flux to the solder joints, promoting better adhesion and preventing oxidation.

Having these tools on hand will not only make the desoldering process easier but also safer for the components you’re working with. Investing in high-quality tools will ensure that you desolder effectively and minimize any potential damage to the electronic parts.

Soldering Iron

A soldering iron is a tool used for joining components and wires together by melting solder. It is an essential tool for soldering and desoldering processes. The soldering iron typically has a heated metal tip that can reach high temperatures.

Types of Soldering Iron

There are various types of soldering irons available, including:

Solder Sucker Desoldering Desolder Remover Pump Tool Vacuum (Desoldering Pump)
Solder Sucker Desoldering Desolder Remover Pump Tool Vacuum (Desoldering Pump)
£5.99
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am
  • Standard Soldering Irons: These are the most common types and come with a tip that can be replaced or changed based on the requirement. They are suitable for general soldering tasks.
  • Temperature-Controlled Soldering Irons: These irons have adjustable temperature settings, allowing the user to control the temperature based on the specific soldering task. They are ideal for more delicate electronic components.
  • Soldering Stations: These are advanced soldering tools that consist of a soldering iron, temperature control unit, and other features like built-in soldering iron holders and cleaning sponges. They provide precise temperature control and are preferred by professionals.

Parts of a Soldering Iron

A soldering iron generally consists of the following parts:

  1. Handle: The handle provides a comfortable grip and insulation from the heated tip.
  2. Heating Element: The heating element is responsible for heating the tip of the soldering iron.
  3. Tip: The tip is the part of the soldering iron that comes in contact with the solder and the components to be joined.
  4. Power Cord: The power cord supplies electricity to the soldering iron.
  5. Temperature Control: Some soldering irons come with temperature control features, allowing the user to adjust the temperature as required.

It is essential to choose a soldering iron based on the specific soldering task and the type of components being worked on. Additionally, following proper safety precautions and using the appropriate soldering techniques are crucial for successful soldering and desoldering processes.

Soldering Pump

A soldering pump, also known as a desoldering pump, is a tool used to remove solder from electronic circuit boards or components. It is a handheld device that consists of a cylindrical tube attached to a plunger mechanism.

See also  How Many Amps Does A Soldering Iron Use

Function

The soldering pump works by creating a vacuum that sucks up molten solder. When heated with a soldering iron, the solder becomes liquid and can be easily drawn into the pump. The plunger is then pressed down, creating suction and pulling the solder into the tube.

Usage

To use a soldering pump, first, heat up the soldered joint you want to remove using a soldering iron. Once the solder is molten, position the pump with the nozzle close to the joint. Press the button or trigger on the pump to activate the vacuum, and quickly release it to suck up the molten solder.

Youmile Solder Sucker Desoldering Vacuum Pump Solder Removal Tool Soldering Accessories with Desoldering Wick, 2 Pcs Spare Nozzle, 2 Pcs Heat Resistant Hose
Youmile Solder Sucker Desoldering Vacuum Pump Solder Removal Tool Soldering Accessories with Desoldering Wick, 2 Pcs Spare Nozzle, 2 Pcs Heat Resistant Hose
£6.99
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

It’s important to be careful with the soldering pump to avoid damaging the surrounding components or the circuit board itself. Always hold the pump at a slight angle to prevent the nozzle from touching any sensitive parts.

Benefits

  • Quick and efficient solder removal: The soldering pump provides a fast and effective way to desolder without the need for additional tools.
  • Versatile: It can be used on various electronic components, such as through-hole resistors, capacitors, and integrated circuits.
  • Cost-effective: Investing in a soldering pump is a cost-effective option for DIY electronics enthusiasts or professionals who frequently work with soldered components.
  • Non-destructive: Unlike other desoldering methods that may damage the component or circuit board, the soldering pump allows for precise and controlled desoldering.

Overall, the soldering pump is an essential tool for anyone involved in electronics repair or DIY projects. It simplifies the process of desoldering and ensures the preservation of valuable components.

Solder Wick

Solder wick, also known as desoldering wick or desoldering braid, is a highly effective tool for desoldering components from circuit boards. It consists of a thin, braided copper wire coated with flux, which helps to facilitate the soldering process.

When using solder wick, follow these steps:

  1. Cut a small section of solder wick: Using scissors or a pair of wire cutters, cut a small piece of solder wick that is long enough to cover the length of the solder joint you want to desolder.
  2. Place the solder wick over the solder joint: Carefully position the solder wick over the solder joint, ensuring that it makes direct contact with the solder.
  3. Heat the solder wick and the solder joint: Use a soldering iron to heat the solder wick and the solder joint simultaneously. Apply heat until the solder melts and is absorbed by the wick.
  4. Remove the solder wick: Once the solder has melted and been absorbed, remove the solder wick by gently pulling it away from the circuit board. Be careful not to damage the circuit board or surrounding components.

Note: It’s important to use the correct size solder wick for the job. A larger braid will absorb solder more quickly, while a smaller braid is better for precision work. Additionally, it’s a good idea to clean the tip of the soldering iron with a wet sponge between each use to remove any residue and ensure optimal performance.

ShineNow No Clean Desoldering Braid Solder Wick Width 2mm Length 3Meters 3PCS Pack
ShineNow No Clean Desoldering Braid Solder Wick Width 2mm Length 3Meters 3PCS Pack
£8.99
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

Benefits of Using Solder Wick

Using solder wick offers several benefits:

  • Efficient desoldering: Solder wick provides a quick and efficient way to remove solder from circuit board components, allowing for easy replacement or repair.
  • Low risk of damage: When used correctly, solder wick minimizes the risk of damage to the circuit board or surrounding components, as it absorbs the solder without putting excessive strain or heat on other parts.
  • Clean results: Solder wick leaves behind clean and undamaged solder pads, making it easier to install new components or make repairs.

When desoldering components, solder wick is a reliable and essential tool that every electronics enthusiast should have in their toolkit.

Preparing for Desoldering

Before you begin the desoldering process, it’s important to gather all the necessary tools and materials. These include:

See also  Best Soldering Iron For White Metal Kits

Soldering iron: Make sure you have a soldering iron with a small, pointed tip. This will allow you to heat up the solder joints effectively.

Solder wick or desoldering braid: This is used to absorb the molten solder and remove it from the board. Make sure you have enough wick for the job at hand.

MG Chemicals 424 Desoldering Braid #2 Fine Braid Super Wick with RMA Flux, 5' Length x 0.05" Width, Yellow
MG Chemicals 424 Desoldering Braid #2 Fine Braid Super Wick with RMA Flux, 5' Length x 0.05" Width, Yellow
£16.06
Amazon.co.uk
Amazon price updated: October 15, 2024 9:11 am

Flux: Flux helps to improve the flow of solder and aids in the desoldering process. You can apply flux to the solder joints before heating them up.

Anti-static wrist strap: This is important to prevent any damage to the electronic components from static electricity. Make sure you wear the strap and connect it to a grounded surface.

Pliers or tweezers: These tools will come in handy for removing any remaining components or wires after desoldering.

Cleaning supplies: It’s important to clean the solder joints and the surrounding area after desoldering. Use a soft brush, cotton swabs, and isopropyl alcohol to clean the area properly.

Work area: Make sure you have a clean and well-lit work area to perform the desoldering process. Having a comfortable and organized space will help you work more efficiently and prevent accidents.

Safety goggles: Remember to wear safety goggles to protect your eyes from any solder splatters or debris that may occur during the desoldering process.

By gathering all the necessary tools and materials and setting up a suitable work area, you’ll be well-prepared for the desoldering process.

Cleaning the Soldering Iron

It is important to keep your soldering iron clean to ensure proper functionality and prevent contamination of your soldering joints. Here are some tips on how to clean your soldering iron:

1. Turn off the soldering iron

Before cleaning, make sure your soldering iron is turned off and unplugged from the power source. This will ensure your safety and prevent any accidental burns.

2. Wipe the soldering iron tip

Take a damp sponge or cloth and gently wipe the soldering iron tip. This will remove any excess solder or flux residue that may have accumulated. Be careful not to scrub too hard, as this can damage the tip.

3. Remove stubborn residue

If there is stubborn residue on the soldering iron tip, you can use a brass wire brush or a soldering iron tip cleaner. Gently scrub the tip until the residue is removed. Avoid using steel wool or abrasive materials, as they can scratch the surface of the tip.

4. Tin the soldering iron tip

After cleaning, it is important to tin the soldering iron tip. This involves applying a thin layer of solder to the tip. Tinning helps to protect the tip and promote better heat transfer. To tin the tip, heat the iron and touch the solder wire to the tip until it melts and evenly coats the surface.

Remember to clean your soldering iron regularly, especially if you notice a decrease in performance or if the tip becomes blackened or corroded. By following these cleaning tips, you can extend the lifespan of your soldering iron and ensure high-quality soldering joints.

Questions and answers

What is soldering iron?

A soldering iron is a hand tool used in soldering. It has a metal tip that gets heated up and is used to melt solder to join two or more metal parts together.

Why would I need to desolder using a soldering iron?

You may need to desolder using a soldering iron when you want to remove or replace a component on a circuit board, or when you want to fix a faulty solder joint.

What tools do I need to desolder using a soldering iron?

To desolder using a soldering iron, you will need a soldering iron with a fine tip, desoldering wick or a desoldering pump, flux, and a soldering iron stand or holder.

Harrison Clayton
Harrison Clayton

Meet Harrison Clayton, a distinguished author and home remodeling enthusiast whose expertise in the realm of renovation is second to none. With a passion for transforming houses into inviting homes, Harrison's writing at https://thehuts-eastbourne.co.uk/ brings a breath of fresh inspiration to the world of home improvement. Whether you're looking to revamp a small corner of your abode or embark on a complete home transformation, Harrison's articles provide the essential expertise and creative flair to turn your visions into reality. So, dive into the captivating world of home remodeling with Harrison Clayton and unlock the full potential of your living space with every word he writes.

The Huts Eastbourne
Logo