How To Resaw Wood On A Table Saw
Resawing wood on a table saw is a technique used by woodworkers to create thinner boards from thicker stock. It is a cost-effective way to maximize the use of your lumber and create custom-sized pieces for your projects. With the right setup and a few key steps, you can achieve clean and accurate resaw cuts on your table saw.
Step 1: Choose the right blade
The first step in resawing wood on a table saw is selecting the right blade. A resaw blade typically has a low TPI (teeth per inch) count, which allows for faster and smoother cuts in thicker stock. Look for a blade with a wide gullet to help clear out sawdust and prevent overheating. A 1/2-inch blade with 3-4 TPI is a good choice for most resawing tasks.
Step 2: Set up the fence
Next, you’ll need to set up the fence on your table saw. The fence should be parallel to the blade and positioned so that the desired thickness of the resawn board is on the waste side of the cut. Use a measuring tape or a digital gauge to ensure accuracy. Make sure the fence is securely locked in place before proceeding.
Step 3: Adjust the blade height
Before making the resaw cut, you’ll need to adjust the height of the blade. The blade should be raised so that it extends above the top edge of the stock by about 1/8 to 1/4 inch. This will allow for easy cutting and prevent binding. Use a blade height gauge or the saw’s built-in adjustment mechanism to set the blade height.
Resawing wood on a table saw requires proper technique and caution. Always wear appropriate safety gear, such as goggles and gloves, and make sure you have a clear workspace. Keep in mind that resawing can create a lot of sawdust, so it’s important to have a dust collection system in place or work in a well-ventilated area.
By following these steps and practicing good technique, you’ll be able to resaw wood on a table saw with confidence. Whether you’re creating veneers, thin stock for box making, or custom-sized boards for your projects, resawing is a valuable skill that can save you time and money in the workshop.
Resawing Wood: A Step-by-Step Guide
If you’re looking to get more out of your woodworking projects, learning how to resaw wood on a table saw is a valuable skill to have. Resawing allows you to cut a thick piece of wood into two or more thinner pieces, which can be useful for a variety of applications.
Here is a step-by-step guide to help you get started:
- Step 1: Set up your table saw – Make sure the blade is properly aligned and at the appropriate height for the resaw cut.
- Step 2: Choose the right blade – Select a blade specifically designed for resawing, such as a wide-kerf blade with a low tooth count.
- Step 3: Prepare the wood – Ensure the piece of wood you’re planning to resaw is flat, square, and free from any defects or imperfections.
- Step 4: Mark your cut – Use a straightedge and pencil to mark the line where you want to make the resaw cut.
- Step 5: Set up the fence – Adjust the table saw fence to the desired distance from the blade, ensuring it runs parallel to the blade.
- Step 6: Make the initial cut – Turn on the table saw and slowly feed the wood into the blade, keeping a firm grip on the wood and using a push stick or push block for safety.
- Step 7: Repeat the process – After making the initial cut, flip the wood over and make another pass to complete the resaw cut.
- Step 8: Sand and finish – Once you have your resawn pieces, use sandpaper or a planer to smooth out any rough edges and apply a finish if desired.
Resawing wood on a table saw can open up a whole new world of possibilities for your woodworking projects. With a little practice and the right techniques, you’ll be able to create thinner boards for a variety of applications, from veneering to joinery. Follow this step-by-step guide to get started on your resawing journey!
Understand the Basics of Resawing
Resawing is a technique used to cut a thick piece of wood into thinner pieces. It is a valuable skill to have if you want to save money on buying pre-cut wood or if you need specific dimensions for your woodworking projects. Here are the basics of resawing that you need to understand before attempting this technique.
1. Selecting the Right Blade
One of the most important aspects of successful resawing is using the right blade. A well-suited blade should have a low tooth count and wide gullets to clear out the waste material effectively. It’s recommended to use a blade specifically designed for resawing to achieve the best results.
2. Preparing the Wood
Before starting the resawing process, make sure the wood is flat, straight, and free of defects. Joint one face and one edge of the wood to create a reference surface for the table saw. Ensure that the wood is securely clamped to prevent any movement during cutting.
3. Adjusting the Table Saw
To achieve accurate cuts, it’s crucial to adjust your table saw properly. Set the blade height slightly higher than the wood’s thickness to avoid binding, but not too high to prevent excessive tear-out. Use a fence to guide the wood and set it parallel to the blade. Double-check all measurements and alignments before making any cuts.
4. Making the Cut
Start by slowly pushing the wood against the blade, ensuring it stays in contact with the fence at all times. Apply consistent pressure to feed the wood through the blade, but avoid forcing it. Keep a steady pace throughout the cut to prevent excessive friction and heat buildup.
5. Dealing with the Resaw Veneer
Once you’ve completed the resaw cut, you’ll be left with thin veneer-like pieces. These pieces are often warped or uneven due to the cutting process. To correct this, use a jointer or planer to flatten the veneer and bring it to the desired thickness.
By understanding these basics of resawing, you’ll be able to successfully transform thick pieces of wood into thinner stock for your woodworking projects. Remember to prioritize safety and precision when using a table saw, and practice your technique to achieve consistent and accurate cuts.
Prepare the Workpiece
Before you can resaw wood on a table saw, you need to properly prepare the workpiece. This involves choosing the right type of wood and making sure it is the correct size and shape.
Choose the right type of wood: Different types of wood have different characteristics, so it’s important to choose the right one for your project. Some types of wood are easier to resaw than others, so consider factors such as hardness, density, and grain direction when making your selection.
Ensure the workpiece is the correct size: Resawing requires a tall and wide workpiece, so make sure your piece of wood is large enough to accommodate the resawing process. It’s also important to ensure that the workpiece is square and flat, as any irregularities can affect the quality of the resawed pieces.
Shape the workpiece if necessary: If your workpiece is not already the desired shape, you may need to shape it before resawing. This can include trimming edges or corners, rounding out curves, or creating a specific profile. Use appropriate tools such as a miter saw or bandsaw to shape the workpiece accurately.
Set up the Table Saw
Before beginning the process of resawing wood on a table saw, it is important to properly set up the table saw. This will ensure safety and accuracy during the cutting process. Here are the steps to set up the table saw for resawing:
1. Adjust the blade: Start by ensuring that the table saw blade is in perfect alignment with the miter gauge slots. Use a combination square to make precise adjustments if needed. Additionally, check that the blade is square to the table surface to prevent any unwanted beveling during the cutting process.
2. Install a resawing blade: Switching to a resawing blade, with a narrower kerf, will make the process more efficient and accurate. Choose a blade specifically designed for resawing to achieve the best results.
3. Adjust the fence: The fence should be aligned parallel to the blade to ensure that the wood is kept straight while resawing. Measure the distance between the blade and the fence at the front and back ends to ensure it is consistent. Make any necessary adjustments using the fence adjustment mechanism on your table saw.
4. Install a featherboard: To prevent the wood from wandering or slipping during the cutting process, it is recommended to use a featherboard. Install a featherboard on the side of the fence opposite to the blade. This will apply pressure to the wood, keeping it firmly against the fence while minimizing the risk of kickback.
5. Set the blade height: Adjust the height of the blade so that it is slightly higher than the thickness of the wood being resawn. This will prevent excessive strain on the blade and minimize burning.
By following these steps to set up the table saw, you will ensure a safe and efficient resawing process. Always remember to wear appropriate safety gear, such as safety glasses and hearing protection, and to feed the wood into the blade smoothly and steadily to achieve the desired results.
Adjust the Fence and Blade
To ensure a smooth and accurate resawing process, it’s crucial to properly adjust the fence and blade on your table saw.
Fence: Start by aligning the fence parallel to the blade. Use a measuring tool, such as a tape measure or a square, to ensure the distance between the back of the blade and the fence is equal along its entire length. This will prevent the wood from binding or getting stuck during the resawing process.
Note: Always refer to your table saw’s user manual for specific instructions on adjusting the fence.
Blade: Next, make sure the blade on your table saw is properly aligned and set to the correct height. A misaligned blade can lead to uneven cuts and potentially dangerous situations. Use a tool, such as a combination square or a digital angle gauge, to ensure the blade is perfectly perpendicular to the table surface.
Additionally, adjust the blade height according to the desired thickness of the resawn wood. Lower the blade for thinner cuts and raise it for thicker cuts. Always make gradual height adjustments and avoid setting the blade too high, as this can increase the risk of kickback and accidents.
Note: Always wear appropriate safety gear, such as safety glasses and hearing protection, when operating a table saw.
By properly adjusting the fence and blade on your table saw, you’ll be able to achieve accurate and precise resawing results.
Make the Resawing Cut
Before making the resawing cut, make sure you have set up your table saw properly. Adjust the blade height so that it is just slightly higher than the thickness of the wood you are resawing. This will help prevent binding and ensure a smooth cut.
When making the cut, position the wood against the fence so that the desired edge is facing towards you. Use a push stick or a push block to safely guide the wood through the blade. Keep your hands clear of the blade and stay focused on the task.
Start the cut by gently pushing the wood forward into the blade. Apply even pressure as you guide the wood through the cut. Take your time and let the blade do the work. Do not force the wood through the cut as this could result in an uneven or jagged cut.
As you near the end of the cut, use a push stick or a push block to safely guide the last few inches of the wood through the blade. This will help maintain control and prevent kickback
Once the cut is complete, turn off the table saw and wait for the blade to come to a complete stop before removing the wood. Check the cut for accuracy and smoothness. If necessary, use a jointer or hand plane to smooth out any rough edges.
Resawing can be a useful technique for creating thin boards or obtaining specific grain patterns from thicker pieces of wood. With the right setup and proper technique, you can achieve clean, straight cuts with your table saw.
Remember to always follow safety precautions when working with power tools, and wear appropriate safety gear, such as goggles and ear protection.
Finish and Clean the Resawn Wood
Once you have successfully resawn the wood on your table saw, it is important to finish and clean the surfaces to achieve the desired result.
Start by using sandpaper to smooth out any rough edges or surfaces. Begin with a coarse-grit sandpaper and gradually move to finer grits for a polished finish. Sand in the direction of the grain to avoid scratching or damaging the wood.
After sanding, wipe off any accumulated dust with a clean cloth or use compressed air to blow away debris. This will ensure a clean surface for the finishing process.
Choose a suitable finish based on your desired outcome. Common options include varnish, oil, or wax. Apply the finish evenly, following the manufacturer’s instructions. Allow it to dry completely before handling the wood.
Once the finish is dry, inspect the wood for any flaws or imperfections. If necessary, do some touch-up sanding or apply an additional coat of finish to achieve the desired result.
Finally, take the time to clean up your workspace. Discard any waste materials properly and store your tools in a safe place. Keeping your workspace tidy will make future projects easier and more enjoyable.
By following these steps, you can effectively finish and clean the resawn wood to achieve a professional-looking result. Take your time and enjoy the process of transforming rough lumber into a beautiful finished product!
Questions and answers
What is resawing wood?
Resawing wood is the process of cutting a board into thinner pieces along its width.
Why would I want to resaw wood?
There are several reasons why you might want to resaw wood. One reason is to create thinner boards for specific projects. Another reason is to maximize the use of expensive or hard-to-find wood by creating multiple boards from a single piece.
Can I resaw wood on a table saw?
Yes, you can resaw wood on a table saw, but you need to make sure you have the right equipment and take proper safety precautions.
What equipment do I need to resaw wood on a table saw?
To resaw wood on a table saw, you will need a sharp resaw blade, a resaw fence or jig, and a push stick or push block for safety.
What are some safety precautions to take when resawing wood on a table saw?
When resawing wood on a table saw, it’s important to wear eye protection, use a splitter or riving knife to prevent kickback, and use a push stick or push block to keep your hands away from the blade.